PowerShot A310
Specifications

Type of Camera
Compact digital still camera with built-in flash and 5.1x digital zoom
Image Capture Device
Type
1/2.7 inch type
Total Pixels
Approx. 3.3 Million
Effective Pixels
Approx. 3.2 Million
Lens
Focal Length
5.0mm (35mm film equivalent: 33mm)
Digital Zoom
5.1x
Focusing Range
Normal AF: 20cm (7.9 in.) - Infinity
Macro AF: 5 - 20cm (2 - 7.9 in.)
Autofocus System
5-point AiAF/1-point AF (Fixed to center)
Viewfinder & Monitor
Viewfinder
Inverted Galilean type
LCD Monitor
1.5" low-temperature polycrystalline silicon TFT color LCD
LCD Pixels
Approximately 7,800 pixels
LCD Coverage
100%
Aperture and Shutter
Maximum Aperture
f/3.6 - 5.6
Shutter Speed
1 - 1/2,000 sec. Shutter speeds slower than 1/6 sec. are only available in select modes
Exposure Control
ISO Sensitivity
AUTO; ISO 50/100/200/400 equivalent
Light Metering Method
Evaluative / Center-weighted average / Spot*
*Metering frame when spot is center fixed
Exposure Control Method
Program AE
Exposure Compensation
+/- 2.0EV in 1/3-stop increments
AE Lock
Not Available
White Balance
White Balance Control
Auto, Pre-set (Daylight, Cloudy, Tungsten, Fluorescent, Fluorescent H), or Custom White Balance
Flash
Built-in Flash
Operation Modes: Auto, Red-Eye Reduction On/Off, Slow-Sync
Flash Range
20cm - 2.0m/7.9 in. - 6.6 ft. (When ISO speed is set to AUTO)
Recycling Time
Approx. 10 sec. or less
Shooting Specifications
Shooting Modes
Auto, Manual, Stitch Assist, Movie
Photo Effects
Vivid, Neutral, Low Sharpening, Sepia and Black & White
Self-Timer
Operates with approx. 2 sec. or approx 10 sec. count-down
Wireless Control
Not Available
Continuous Shooting
Approx. 2.2 shots/sec. (Large/Fine Mode and LCD monitor is Off)
Image Storage
Storage Media
CompactFlash (CF) Card Type I
File Format
AVI (Image data: Motion JPEG; Audio data: WAVE (Monaural))
Print Order Format
Digital Print Order Format (DPOF) Version 1.1
Image Compression
JPEG (Exif 2.2 compliant)
JPEG Compression Mode
SuperFine, Fine or Normal
Number of Recording Pixels
Still Image: 2,048 x 1,536 (Large), 1,600 x 1,200 (Medium 1), 1,024 x 768 (Medium 2), 640 x 480 (Small)
Movie: 640 x 480, 320 x 240, 160 x 120
Playback Specifications
Playback Modes File
Single, Index (9 thumbnails), Magnification (approx. 2x to 10x)
Erasing Specifications
Erase Modes
Still Image: Single Image, All Images
Movie: Part of Movie, All Movie
Interfaces
Computer Interface
Universal Serial Bus (USB) (mini-B jack)
Video Out
None
Other
CF card slot (accept type I cards). Direct connection to Canon CP Printers and select Bubble Jet Photo Printers (no computer required).
Power Supply
Power Source
1. Size AA Alkaline battery x2
2. Rechargeable size AA NiMH battery x2
3. Compact power adapter CA-PS800

Shooting Capacity
AA ALKALINE: LCD On - Approx. 75 shots; LCD Off - Approx. 250 shots
AA NIMH: LCD On - Approx. 350 shots; LCD Off - Approx. 950 shots
Playback Time
Approx. 90 min/Approx 240 min. (Alkaline battery/NB-2AH)
Physical Specifications
Operating Temperature
32 - 104°F (0 - 40°C)
Operating Humidity
10 - 90%
Dimensions (WxHxD)
4.33 x 22.8 x 14.4 in./110.0 x 58.0 x 36.6mm (Excluding protrusions)
Weight
Approx. 6.17 oz./175g (Camera body only)
Computer System Requirements
Mac Requirements
OS: Mac OS 9.0 - 9.2, Mac OS X (v10.1/10.2/10.3).
Computer Model: The above OS should be pre-installed on computer with built-in USB ports.
CPU: PowerPC.
Interface: USB (Models with Apple genuine USB interface only).
PC Requirements
OS: Microsoft Windows 98 (including Second Edition)/ME/2000/XP.
Computer Model: The above OS should be pre-installed on computer with built-in USB ports.
CPU: Pentium 150MHz or higher processor (Windows 98/ME/2000), Pentium 300MHz or higher processor (Windows XP).
Interface: USB (Windows 98/ME/2000/XP pre-install model only).

File Name WIP625.exe

File Size 5.57 MB
           


Download and Installation Instructions
   

Overview
This driver is PTP (Picture Transfer Protocol) compliant the WIA driver for Windows XP made by Canon.
Changes
- The problem wherein uninstallation was not performed properly has been fixed.
Important
If you connect your camera to the Computer (OS: Windows XP) with a USB cable, it is not necessary to install the driver as your camera supports PTP and the standard driver of Windows XP.
However, there are some limitations as follows.
In this case, you need to download "Canon Camera WIA Driver 6.4.0 for Windows XP" below.
1. When a camera with a lot of images inside is connected and if you want to download images to your computer using Windows Explorer or [Cameras and Scanners Wizard], it may take a lot of time before starting to show thumbnails or starting the wizard.
* Time differs depending on the surroundings of the computer.
* It does not apply to uploading images to the computer using Canon brand applications (Ex. ZoomBrowser EX).
2. When a camera with a lot of images inside is connected and if you download images to the computer using ZoomBrowser EX, the following [Server Busy] message may be displayed in some case.
When this message is displayed, click the [Switch to..] button.
If the same message is displayed again, click the [Switch to..] button again till the message disappears.
Downloading and Installing the driver
- Perform the following download procedures.
- The driver is saved as a self-extracting, compressed file and it will be automatically installed.
1. Click the download file below, and then click [Save] in the [Download File] dialog box that appears.
* When you click [Open] in this dialog box, the procedures that follow below will be performed automatically (to step 4).
2. Specify the download destination (ex. Desktop), and then click [Save].
The file will be downloaded to the destination you specified in .exe format.
3. Double-click the downloaded file. The contents of the file will be extracted automatically.
4. When the extraction is complete, installation will start automatically.
If the installation is canceled before completion
If the installation is canceled, the temporary folder created during extraction will disapear. Restart the installation from step 3 above if you wish to install the driver again. If you clicked [Open] instead of saving the downloaded file in step 1, and also canceled the installation before it was complete, download the file again and perform the procedure above from the beginning.
?
5. the Language selection panel will be shown. Select the language of the driver, then click [OK].
6. When the install wizard is displayed, click [Next].
7. In the [Area Selection] panel, select the residential area and click [Next].
8. Click [Yes].
9. Click [Next].
10. When copying files process is finished, [WIA Driver Update Utility] dialog box will be displayed.
Follow the onscreen instructions to connect the camera to the computer with the USB cable.
If the [Event] dialog that allows you to select an application program to start, click [Cancel]. Close any applications which have automatically started.
11. Confirm that the name of the camera connected is displayed, and click [OK].
12. When the message [Driver has been updated] is shown, the installation is completed.
Click [OK], then the [Event] dialog box will appear allowing you to select an application program to start.
13. Click [Finish]. This will end the installation.

click here to download
You are not  allowed to view links.
Register or Login